|
|
|
| Precise Optimization of 3D Bio-Printing Cell-Laden Hydrogel Construct |
| Huang Mengjie1 , Luo Li1, Wang Ling1,2*, Xu Mingen1,2* |
1(School of Life Information Instrument and Science Engineering, Hangzhou Dianzi University, Hangzhou 310018, China)
2(Zhejiang Provincial Key Lab of Medical Information and Three-Dimensional Bio-Printing, Hangzhou 310018, China) |
|
|
|
|
Abstract The combination of 3D bio-printing technology and hydrogel provides an attractive solution for manufacturing tissues and organs with complex structures and functions. The internal constructs can be custom-printed to imitate the 3D microenvironment of tissues and organs, which is critical for cell growth, tissue formation and regeneration after printed. However, precise matching between the printed and the design is still challenging due to variable physical and chemical properties of hydrogel. In this paper, an optimized method based on optical coherence tomography (OCT) for 3D bio-printing cell-laden hydrogel construct was proposed. The tissue was imaged by 3D non-destructive homemade OCT system, and quantitatively characterized, then the mismatch of structural parameters between the design and the printed was reduced using the experimentally obtained equations, and the accuracy and stability of 3D bio-printing were improved. The results demonstrated that the deviation of the key structural parameters between the printed and the design was controlled to less than 7%, which was much lower than the deviation about 40% reached by conventional 3D bio-printing. The controlled parameters included pore size, strut size, porosity, surface area and pore volume. And the cell viability of two weeks incubation was increased from about 80% to over 90%. It was concluded that online quantitative evaluation and feedback iterative analysis system based on OCT provided a potential tool for mass customization of cell-laden hydrogel tissues, 3D bio-printing tissues and organs.
|
|
Received: 01 September 2017
|
|
|
|
Corresponding Authors:
E-mail: lingw@hdu.edu.cn, xumingen@hdu.edu.cn
|
|
|
|
[1] Murphy SV, Atala A. 3D bioprinting of tissues and organs [J]. Nat Biotechnol, 2014, 32(8):773-785.
[2] Derby B. Printing and prototyping of tissues and scaffolds [J]. Science, 2012, 338(6109):921-926.
[3] Kang HW, Lee SJ, Ko IK, et al. A 3D bioprinting system to produce human-scale tissue constructs with structural integrity [J]. Nat Biotechnol, 2016, 34(3):312-319.
[4] Billiet T, Vandenhaute M, Schelfhout J, et al. A review of trends and limitations in hydrogel-rapid prototyping for tissue engineering [J]. Biomaterials, 2012, 33(26): 6020-6041.
[5] Wang S, Lee JM, Yeong WY. Smart hydrogels for 3D bioprinting [J]. International Journal of Bioprinting, 2015, 1(1): 3-14.
[6] Fedorovich NE, De Wijn JR, Verbout AJ, et al. Three-dimensional fiber deposition of cell-laden, viable, patterned constructs for bone tissue printing [J]. Tissue Eng Part A, 2008, 14(1): 127-133.
[7] Wang Xiaohong, Yan Yongnian, Pan Yuqiong, et al. Generation of three-dimensional hepatocyte/gelatin structures with rapid prototyping system [J]. Tissue Eng, 2006, 12(1): 83-90.
[8] He Yong, Yang Feifei, Zhao Haiming, et al. Research on the printability of hydrogels in 3D bioprinting [J]. Sci Rep, 2016, 6(6):29977.
[9] Shim JH, Kim JY, Park M, et al. Development of a hybrid scaffold with synthetic biomaterials and hydrogel using solid freeform fabrication technology [J]. Biofabrication, 2011, 3(3): 034102.
[10] Chang R, Nam J, Sun W. Effects of dispensing pressure and nozzle diameter on cell survival from solid freeform fabrication-based direct cell writing [J]. Tissue Eng Part A, 2008, 14(1): 41-48.
[11] Billiet T, Gevaert E, De Schryver T, et al. The 3D printing of gelatin methacrylamide cell-laden tissue-engineered constructs with high cell viability [J]. Biomaterials, 2014, 35(1): 49-62.
[12] Zhu Jiang, Qi Li, Miao Yusi, et al. 3D mapping of elastic modulus using shear wave optical micro-elastography [J]. Sci Rep, 2016, 6:35499.
[13] Zhu Jiang, Qu Yueqiao, Ma Teng, et al. Imaging and characterizing shear wave and shear modulus under orthogonal acoustic radiation force excitation using OCT Doppler variance method [J]. Opt Lett, 2015, 40(9): 2099-2102.
[14] Appel AA, Anastasio MA, Larson JC, et al. Imaging challenges in biomaterials and tissue engineering [J]. Biomaterials, 2013, 34(28): 6615-6630.
[15] Wang Ling, Xu Mingen, Zhang Lielie, et al. Automated quantitative assessment of three-dimensional bioprinted hydrogel scaffolds using optical coherence tomography [J]. Biomed Opt Express, 2016, 7(3): 894-910.
[16] 王玲, 涂沛, 石然,等. 光学相干层析成像技术用于三维生物打印水凝胶支架结构的定量评价研究 [J]. 中国激光, 2015, 42(8): 123-131.
[17] 王玲, 张烈烈, 周青青,等. 基于光学相干层析的水凝胶三维打印精准控制研究 [J]. 中国激光, 2016(6): 191-200.
[18] 王玲, 朱海龙, 涂沛,等. 基于LabVIEW的高速三维扫频光学相干层析成像系统 [J]. 中国激光, 2014, 41(7): 125-132.
[19] Yang Ying, Dubois A, Qin Xiangpei, et al. Investigation of optical coherence tomography as an imaging modality in tissue engineering [J]. Phys Med Biol, 2006, 51(7): 1649-1659.
[20] Chen Chaowei, Betz MW, Fisher JP, et al. Macroporous hydrogel scaffolds and their characterization by optical coherence tomography [J]. Tissue Eng Part C Methods, 2011, 17(1): 101-112.
[21] Xu Mingen, Wang Xiaohong, Yan Yongnian, et al. An cell-assembly derived physiological 3D model of the metabolic syndrome, based on adipose-derived stromal cells and a gelatin/alginate/fibrinogen matrix [J]. Biomaterials, 2010, 31(14): 3868-3877.
[22] 胡金夫, 徐铭恩, 徐莹,等. 基于细胞三维受控组装技术的细胞芯片构建 [J]. 中国生物医学工程学报, 2012, 31(3): 374-381.
[23] 石然, 徐铭恩, 周青青,等. 基于细胞3D打印技术的体外肿瘤模型构建研究 [J]. 中国生物医学工程学报, 2015, 34(5): 618-622.
[24] Zhao Yingdi, Tan Ke, Zhou Yan, et al. A combinatorial variation in surface chemistry and pore size of three-dimensional porous poly(ε-caprolactone) scaffolds modulates the behaviors of mesenchymal stem cells [J]. Mater Sci Eng C Mater Biol Appl, 2016, 59: 193-202. |
|
|
|
