|
|
Research on the Relationship Between Mechanical Properties of 3D Printed Hydroxyapatite Scaffolds and Inner Structures |
Li Xiangcheng1, Suo Hairui2,3, Wang Ling2,3, Xu Mingen2,3* |
1(School of Life Information and Instrument Engineering, Hangzhou Dianzi University, Hangzhou 310018, China) 2(School of Automation, Hangzhou Dianzi University, Hangzhou 310018, China) 3(Zhenjiang Provincial Key Lab of Medical Information and Three-Dimensional Bio-Printing, Hangzhou 310018, China) |
|
|
Abstract 3D printed bone tissue engineering scaffolds are becoming hotspot recently, and preparation of bone tissue engineering scaffolds with high porosity and sufficient mechanical properties is still one of the difficulties in current research. The purpose of this study was to investigate the effects of different filling angle structures on the mechanical properties of 3D printing scaffold with the same porosity. Firstly, three different filling angle (45°, 60°, 90°) scaffold structures with the same porosity were designed by SolidWorks software, the structure of the intersection point was used as the minimum support unit of the scaffold, and it′s mechanical properties were simulated by ABAQUS software. Next, the compression modulus of the structure unit was accumulated to investigate the effect of filling angle on the mechanical properties of the scaffold. Three kinds of hydroxyapatite scaffolds with inner structure were prepared by 3D printing, and the porosity and mechanical properties of the scaffolds were tested to verify the simulation results. Results showed that the compression modulus ratio of the three inner structures obtained by simulation was Es(90°)∶Es(60°)∶Es (45°)=12.3:10.9:10.0. There were no significant differences in the porosity of the hydroxyapatite scaffolds among the three different filling angles (90°, 60°, 45°), and the compression modulus ratio was Es(90°):Es(60°):Es(45°)=15.4:13.1:10.0, consistent with the simulation results. The 90° scaffold had the highest compressive strength (7.36 ± 0.63) MPa and compressive modulus (33.55 ± 2.49) MPa. Compared with the 45° scaffold, the compressive strength of 90° scaffold was increased by 74.8% and the compressive modulus was increased by 55.18%. With the same porosity, the scaffold with smaller area of single pore showed higher compressive modulus and compressive strength. This study provided an analytical method and theoretical basis for the preparation of 3D printed biological scaffolds with optimal inner structure.
|
Received: 11 December 2018
|
|
|
|
|
[1] 周静. 纳米支架材料在骨组织工程应用中的优势 [J]. 临床口腔医学杂志, 2018, 34(10): 633-635. [2] Bose S, Roy M, Bandyopadhyay A. Recent advances in bone tissue engineering scaffolds [J]. Trends in Biotechnology, 2012, 30(10): 546-554. [3] 叶琦,石新莹,曹姗姗,等. 多孔钛孔隙率和孔隙尺寸对其力学性能及细胞相容性的影响 [J]. 口腔材料器械杂志, 2013, 22(1): 7-12. [4] 王雷,李强. 不同孔隙率多孔钛铌合金的生物力学强度及细胞生物相容性 [J]. 中国组织工程研究, 2016, 20(38): 5709-5715. [5] 徐玮,石新莹,关锐峰,等. 孔隙率对多孔镍钛合金力学性能及离子析出量的影响 [J]. 医用生物力学, 2011, 26(4): 349-354. [6] 冯辰栋,夏宇,李祥,等. 3D打印多孔钛支架微观孔隙结构和力学性能 [J]. 医用生物力学, 2017, 32(3): 256-260. [7] 徐广胜,寇宏超,刘向宏,等. 立方孔拓扑结构对多孔钛力学性能的影响 [J]. 稀有金属材料与工程, 2014, 43(11): 2778-2781. [8] Kharmanda G. Integration of multi-objective structural optimization into cementless hip prosthesis design: Improved Austin-Moore model [J]. Computer Methods in Biomechanics and Biomedical Engineering, 2016, 19(14): 1557-1566. [9] Liu YF, Fan YY, Jiang XF, et al. A customized fixation plate with novel structure designed by topological optimization for mandibular angle fracture based on finite element analysis [J]. BioMedical Engineering OnLine, 2017, 16(1): 131-148. [10] 周磊,潘华兴,焦力刚. 可调控纤维增强型骨组织工程支架的制备及表征 [J]. 哈尔滨医科大学学报, 2014, 48(5): 373-375. [11] 岑超德,罗聪. 可降解组织工程骨材料及其血管化研究:问题与应用前景 [J]. 中国组织工程研究, 2014, 18(21): 3391-3397. [12] 陈德敏,刘雪阳. 锶磷灰石多孔陶瓷不同孔隙率对成骨细胞生物学行为的影响 [J]. 组织工程与重建外科, 2006, 2(3): 123-127. [13] 王雷,李强. 不同孔隙率多孔钛铌合金的生物力学强度及细胞生物相容性 [J]. 中国组织工程研究, 2016, 20(38): 5709-5715. [14] 谭树杰,李多生. 激光3D打印80Ni20Cr合金的显微组织及力学性能 [J]. 中国有色金属学报, 2017, 27(8): 1572-1579. [15] 陈哲,刘宇杰,康国政. 闭孔泡沫铝结构参数对其压缩性能影响的有限元分析 [J]. 工程科学与技术, 2012, 44(S2): 84-87. [16] 肖诗云,朱梁. 孔隙对混凝土宏观力学性质的影响 [J]. 沈阳建筑大学学报:自然科学版, 2016, 32(4): 608-618. |
[1] |
Zhang Yifan, Xu Mingen, Wang Ling, Zhang He. Coaxial 3D Bioprinting of Vascular Tissue Engineering Scaffolds forPromoting Endothelial Cell Growth[J]. Chinese Journal of Biomedical Engineering, 2020, 39(2): 206-214. |
[2] |
Liu Yan, Yang Qingzhen, Chen Xiaoming, Gu Fangwei, Zhang Hui. Fabrication of Organ-on-a-Chip by 3D Printing Technology[J]. Chinese Journal of Biomedical Engineering, 2020, 39(1): 97-108. |
|
|
|
|