|
|
Study on a Method for Orientation Design in Dental Implanting Based on Occlusal Center Recovery Mechanical Model |
1 College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics & Astronautics, Nanjing 210016, China
2 Department of Implantology, School of Stomatolog , Nanjing Medical University , Nanjing 210029, China |
|
|
Abstract The direction of dental implant is one of the important factors of longterm success of dental implants. This paper presents a method for the initial orientation design of dental implants based on the occlusal center recovery mechanical model. The occlusal center recovery mechanical model was established with the data from the CT of the patients, the data of the dental cast models and the measured data of occlusal force. The established occlusal center recovery mechanical model was used in the quantitatively studies and to accomplish the initial orientation design. This method can provide the mechanical basis and references for the orientation design of implants, and further provide a new idea for the improvement of surgical guide of the existing implant system. This modeling and design method was applied and observed in six subjects. The results showed both the angle of mesiodistal inclination and the angle of buccolingual inclination are less than 10~15 degrees. Therefore, this method is feasible and effective.
|
|
|
|
|
[1]Ai K,Andreas P,Margareta H,et al. Virtually planned and templateguided implant surgery: an experimental model matching approach[J]. Clin Oral Implants Res, 2011,22(3): 308-313.
[2]施斌,王贻宁. 固定种植义齿设计中的力学因素分析[J]. 国外医学(口腔医学分册), 2001,28(1): 28-30.
[3]李梅梅,熊艳芳. SimPlant在口腔种植手术上的应用[EB/OL]. 上海: 2008. http://211151 8973/admin/cms/1895/images/SimPlant.pdf. 2008-12-20/2013-05-01.
[4]Jack T. Krauser. The use of computerized treatment planning and a customized surgical templateto achieve optimal implant placement[J]. Inside Dentistry, 2008,4(22): 15-17.[5]康璐,黄远亮,顾立栩,等. 计算机辅助设计软件在口腔种植外科的应用研究[J]. 口腔颌面外科杂志, 2008,8(18): 265-268.
[6]吴轶群,张志愿,陈晓军,等. 口腔种植计算机术前规划系统的建立与应用[J]. 中国口腔颌面外科杂志, 2008,6(4): 255-259.
[7]宿玉成. 现代口腔种植学[M]. 北京:人民卫生出版社,2004: 91-93.
[8]Jabero M,Sarment DP. Advanced surgical guidance technology: a review[J]. Implant Dent, 2006,15(2): 135-142.
[9]Spector L. Computeraided dental implant planning[J]. Dent Clin North Am, 2008,52(4):761-775.
[10]温颖,张良琼,谭包生. 单侧游离缺失不同修复方法的咬合力分析[J]. 北京口腔医学, 2008,16(3): 148-151.
[11]郑明,程辉,程祥荣,等. 双端固定桥修复前后基牙最大牙合力变化的研究[J]. 口腔医学研究, 2006,22(6): 678-680.
[12]胡志刚,程辉,郑明,等. 正常牙合牙尖交错位咬合平衡的定量研究[J]. 中华口腔医学杂志, 2006,41(10): 618-620.
[13]周书敏,徐军,谭建国,等. 关于创伤牙合的计算机辅助光牙合研究[J]. 中华口腔医学杂志, 1998,33(1): 44-47.
|
|
|
|